Simtec Coatings
2088 2nd Street MATERIAL SAFETY DATA SHEET
Norco, CA 92860
Transportation
Emergency
Non-Transportation Emergency
Call Chemtrec: 1-800-424-9300 951-279-7010
1. PRODUCT DESCRIPTION:
Product
..: Prestec Adhesion
Promoter for Oily Wood
Product #
..: 58x1 Series
Chemical Name
: Urethane
2. HAZARDOUS INGREDIENTS:
Name/CAS# Exposure limits Concentration
MEK / 78-93-3 200- 300 10- 25 %
MIBK /108-10-1 150- 200 20-35 %
Trade Secret 1 40-60 %
3. HAZARDOUS IDENTIFICATION:
Hazardous Overview
Warning! Color: Clear; Form: Liquid; Odor: Of Solvent; May cause respirator tract
irritation; Inhalation
may cause nausea or dizziness; May cause
eye irritation; May be harmful if
swallowed; Irritating gases/fumes may be
given off during burning or thermal decomposition.
Potential Health
Effects:
Route of Entry
:
Inhalation; skin contact; skin absorption; eye contact
Human Effects and
Symptoms of Overexposure:
Affects of
Overexposure:
..: Breathing Vapors may be irritating ad may
cause nausea, dizziness and loss of consciousness. People with allergies may be greatly affected
Acute Skin Contact
: Based on animal testing (see animal toxicity
section), this product is not expected to be a skin irritant.
Chronic Skin
Contact
: None known.
Acute Eye Contact
.: Based on animal testing, eye contact with
liquid, aerosols and vapors of this product are not
expected to cause eye irritation..
Chronic Eye
Contact
.: None known.
Acute Ingestion
..: Can cause
irritation in the mouth, stomach tissue and digestive tract.
Chronic Ingestion
..: None known.
Carcinogenicity
NTP
.: Not listed.
IRAC
..: Not
listed.
OSHA
.: Not regulated.
MEDICAL CONDITIONS
Exposure Limits
: Not established for product as a whole refer
to section 2 for exposure limits of hazardous constituents.
4. FIRST AID MEASURES:
First Aid For Eyes
.:
Flush with clean, lukewarm water (low pressure) for at least 15 minutes
occasionally lifting eyelids. Obtain
medical attention.
First Aid For Skin
.:
Remove contaminated clothing.
First Aid For
Inhalation
..:
Move to an area free from risk of further exposure. Administer artificial respiration or oxygen
if needed. Obtain medical attention immediately.
First Aid For Ingestion
:
DO NOT INDUCE VOMITING. DO NOT
GIVE ANYTHING BY MOUTH TO AN UNCONCIOUS PERSON.
Consult physician.
5. FIRE FIGHTING MEASURES:
Flash Point
: 21.00
Deg. F
DOT: Flammable liquid or Solid
OSHA Flammable Class IB
Extinguishing Media
..: Dry chemical;
Carbon dioxide; Foam; Water.
Special Fire Fighting
Procedures: Full emergency equipment
with self-contained breathing apparatus should be worn by firefighters. During a fire thermal decomposition and
combustion may generate irritating and toxic gases and aerosols.
Unusual
Fire/Explosion Hazards: Closed container
may explode when exposed to extreme heat.
Use cold water spray to cool fire-exposed containers to minimize risk of
rupture.
6. ACCIDENTAL RELEASE MEASURES:
Spill or Leak
Procedures
: Evacuate non-essential
personnel. Remove all sources of
ignition and ventilate the area. Dike or
impound spilled material and control further spillage if feasible. Notify appropriate authorities if
necessary. Cover spill with sawdust,
vermiculite, Fullers earth or other absorbent material. Collect material and place in a clean empty
drum for disposal. Utilize recommended
protective equipment.
7. HANDING & STORAGE:
Storage Temperature
(min/max.): 41 F (5 C) / 68 F (20 C)
Shelf Life
..: 6 Months
Special
Sensitivity
: Heat, light, moisture
and Isocynate.
Handling/Storage
Precautions
: Stored in closed
containers and in the dark at temperatures less than 68 F (20 C).
8. PERSONAL PROTECTION:
Eye-protection
Requirements
: Splash goggles, safety
glasses or face shield. Contact
lenses should not be worn.
Skin Protection
Requirements
..:
Permeation resistant gloves.
Ventilation/Respiratory
Requirement: Exhaust ventilation
sufficient to keep the airborne concentrations Isocyante
below the appropriate TLVs during curing of coating system must be utilized. Exhaust air may need to be cleaned by
scrubbers & filters to reduce environmental contamination. Curing ovens must be ventilated to prevent
off-gases from entering the workplace.
Use a respirator that is sufficient for an isocynate
exposure.
9. PHYSICAL AND CHEMICAL PROPERTIES:
Physical
Form
.: Liquid
Color
: Colorless to Clear
Odor
.: MEK
Boiling Range
.: 165- 242 Deg. F
Solubility in
Water
.: Insoluble
Specific Gravity
.: 1.12 at 68 F (20 C)
Bulk Density
.: 7.35 lbs per gallon
% Volatile By Weight
..: 22.3 %
VOC
: 5.9 lb/gal
10. STABILITY AND REACTIVITY:
Stability
..: Stable
when stored in dark at temperatures below 68 F (20 C).
Hazardous
Polymerization
: May occur; When exposed to Isocynate.
Incompatibilities
: Aliphatic hydrocarbons.
Instability
Conditions
: None known.
Decomposition
Products
: By fire:
CO2, CO. During curing process:
11. TOXICOLOGICAL INFORMATION:
Acute Toxicity
Oral LD50
: Greater than 5000 mg/kg (rat)
Eye Effects
:
Non-irritant (rabbit)
Skin Effects
: Slightly Irritating, 24h
(rabbit)
12. ECOLOGICAL INFORMATION:
No Ecological Information Available
13. DISPOSAL CONSIDERATIONS:
Waste Disposal
Method
: Waste must be disposed of in
accordance with Federal, State and local environmental control
regulations. Incineration is the
preferred method. Empty containers must
be handled with care due to product residue.
Decontaminate containers prior to disposal.
14. TRANSPORTATION INFORMATION:
Technical Shipping
Name
.: Paint
Freight Class
..: 55
Hazard Class Division
..: 3
UN #
..: UN1263
Packing Group
..: II
Hazard Label
..: Flammable Liquid
Radioactive
..: Non-radioactive
15. REGULATORY INFORMATION:
The following chemicals are
specifically listed by individual states; other product specific health and
safety data in other sections of the MSDS may also be applicable for state
requirements. For details on your
regulatory requirements you should contact the appropriate agency in your
state.
Name/cas #
Concentration State Code
MEK 10-25% CA,
PA1
MIBK 45-65%
CA =
MA =
NJ1 =
PA1 =
PA3 =
16. OTHER INFORMATION: None.
This
information is furnished without warranty, expressed or implied, except that it
is accurate to the best knowledge of Simtec.
The data on this sheet relates only to the material specified
herein. Simtec assumes no legal
responsibility for use or reliance upon these data.
Effective Date: 5-25-10 Approved By: Mike DeVries