2088 2nd Street MATERIAL SAFETY DATA SHEET
Norco, CA 92860
Transportation Emergency Non-Transportation Emergency
Call Chemtrec: 1-800-424-9300 951-279-7010
1. PRODUCT DESCRIPTION:
Product ..: Prestec Adhesion Promoter Catalyst
Product # ..: 58x2 Series
Chemical Name : Urethane
2. HAZARDOUS INGREDIENTS:
Name/CAS# Exposure limits Concentration
MEK / 78-93-3 200- 300 ppm 10- 25 %
PM Acetate/108-65-6 100- 150 ppm 0- 5 %
Tolulene/108-88-3 100-150ppm 30 40 %
Trade Secret 1 25 -35 %
3. HAZARDOUS IDENTIFICATION:
Warning! Color: Clear; Form: Liquid; Odor: Of Solvent; May cause respirator tract irritation; Inhalation may cause nausea or dizziness; May cause eye irritation; May be harmful if swallowed; Irritating gases/fumes may be given off during burning or thermal decomposition.
Potential Health Effects:
Route of Entry : Inhalation; skin contact; skin absorption; eye contact
Human Effects and Symptoms of Overexposure:
Affects of Overexposure: ..: Breathing Vapors may be irritating ad may cause nausea, dizziness and loss of consciousness. People with allergies may be greatly affected
Acute Skin Contact : Based on animal testing (see animal toxicity section), this product is not expected to be a skin irritant.
Chronic Skin Contact : None known.
Acute Eye Contact .: Based on animal testing, eye contact with liquid, aerosols and vapors of this product are not expected to cause eye irritation..
Chronic Eye Contact .: None known.
Acute Ingestion ..: Can cause irritation in the mouth, stomach tissue and digestive tract.
Chronic Ingestion ..: None known.
Carcinogenicity NTP .: Not listed.
IRAC ..: Not listed.
OSHA .: Not regulated.
Exposure Limits : Not established for product as a whole refer to section 2 for exposure limits of hazardous constituents.
<![if !supportLists]>4. <![endif]>FIRST AID MEASURES:
First Aid For Eyes .: Flush with clean, lukewarm water (low pressure) for at least 15 minutes occasionally lifting eyelids. Obtain medical attention.
First Aid For Skin
.: Remove contaminated clothing.
First Aid For Inhalation ..: Move to an area free from risk of further exposure. Administer artificial respiration or oxygen if needed. Obtain medical attention immediately.
First Aid For Ingestion : DO NOT INDUCE VOMITING. DO NOT GIVE ANYTHING BY MOUTH TO AN UNCONCIOUS PERSON. Consult physician.
<![if !supportLists]>5. <![endif]>FIRE FIGHTING MEASURES:
Flash Point : 21.00 Deg. F
DOT: Flammable liquid or Solid
OSHA Flammable Class IB
Extinguishing Media ..: Dry chemical; Carbon dioxide; Foam; Water.
Special Fire Fighting Procedures: Full emergency equipment with self-contained breathing apparatus should be worn by firefighters. During a fire thermal decomposition and combustion may generate irritating and toxic gases and aerosols.
Unusual Fire/Explosion Hazards: Closed container may explode when exposed to extreme heat. Use cold water spray to cool fire-exposed containers to minimize risk of rupture.
6. ACCIDENTAL RELEASE MEASURES:
Spill or Leak Procedures : Evacuate non-essential personnel. Remove all sources of ignition and ventilate the area. Dike or impound spilled material and control further spillage if feasible. Notify appropriate authorities if necessary. Cover spill with sawdust, vermiculite, Fullers earth or other absorbent material. Collect material and place in a clean empty drum for disposal. Utilize recommended protective equipment.
7. HANDING & STORAGE:
Storage Temperature (min/max.): 41 F (5 C) / 68 F (20 C)
Shelf Life ..: 6 Months
Special Sensitivity : Heat, light, moisture and Isocynate.
Handling/Storage Precautions : Stored in closed containers and in the dark at temperatures less than 68 F (20 C).
<![if !supportLists]>8. <![endif]>PERSONAL PROTECTION:
Eye-protection Requirements : Splash goggles, safety glasses or face shield. Contact lenses should not be worn.
Skin Protection Requirements ..: Permeation resistant gloves.
Ventilation/Respiratory Requirement: Exhaust ventilation sufficient to keep the airborne concentrations Isocyante below the appropriate TLVs during curing of coating system must be utilized. Exhaust air may need to be cleaned by scrubbers & filters to reduce environmental contamination. Curing ovens must be ventilated to prevent off-gases from entering the workplace.
Use a respirator that is sufficient for an isocynate exposure.
<![if !supportLists]>9. <![endif]>PHYSICAL AND CHEMICAL PROPERTIES:
Physical Form .: Liquid
Color : Colorless to Clear
Odor .: MEK
Boiling Range .: 165- 242 Deg. F
Solubility in Water .: Insoluble
Specific Gravity .: 1.12 at 68 F (20 C)
Bulk Density .: 7.35 lbs per gallon
% Volatile By Weight ..: 22.3 %
VOC : 5.9 lb/gal
<![if !supportLists]>10. <![endif]>STABILITY AND REACTIVITY:
Stability ..: Stable when stored in dark at temperatures below 68 F (20 C).
Hazardous Polymerization : May occur; When exposed to Isocynate.
Incompatibilities : Aliphatic hydrocarbons.
Instability Conditions : None known.
Decomposition Products : By fire: CO2, CO. During curing process:
<![if !supportLists]>11. <![endif]>TOXICOLOGICAL INFORMATION:
Oral LD50 : Greater than 5000 mg/kg (rat)
Eye Effects : Non-irritant (rabbit)
Skin Effects : Slightly Irritating, 24h (rabbit)
<![if !supportLists]>12. <![endif]> ECOLOGICAL INFORMATION:
No Ecological Information Available
<![if !supportLists]>13. <![endif]>DISPOSAL CONSIDERATIONS:
Waste Disposal Method : Waste must be disposed of in accordance with Federal, State and local environmental control regulations. Incineration is the preferred method. Empty containers must be handled with care due to product residue. Decontaminate containers prior to disposal.
<![if !supportLists]>14. <![endif]>TRANSPORTATION INFORMATION:
Technical Shipping Name .: Paint
Freight Class ..: 55
Hazard Class Division ..: 3
UN # ..: UN1263
Packing Group ..: II
Hazard Label ..: Flammable Liquid
Radioactive ..: Non-radioactive
15. REGULATORY INFORMATION:
The following chemicals are specifically listed by individual states; other product specific health and safety data in other sections of the MSDS may also be applicable for state requirements. For details on your regulatory requirements you should contact the appropriate agency in your state.
Name/cas # Concentration State Code
MEK 10-25% CA, PA1
<![if !supportLists]>16. <![endif]>OTHER INFORMATION: None.
This information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of Simtec. The data on this sheet relates only to the material specified herein. Simtec assumes no legal responsibility for use or reliance upon these data.
Effective Date: 5-25-10 Approved By: Mike DeVries